| Y Axis Foot Lite |
Printed Part |
4 |
Y_Axis_Foot_Lite |
| Y axis Belt Clamp Idler |
Printed Part |
4 |
Y_Axis Belt_Clamp |
| NEMA17 50mm spacer |
Printed Part |
2 |
NEMA17_50mm_spacer |
| Y Gantry link bearing cup |
Printed Part |
2 |
Y_Gantry_link_bearing_cup |
| Yaxis belt bearing idler |
Printed Part |
2 |
Y_Axis_belt_bearing_idler |
| Yaxis belt bearing idler outide_LITE |
Printed Part |
1 |
Y_Axis_Belt_Bearing_Idler_Outide_LITE |
| Yaxis belt bearing idler outide_LITE_Cable |
Printed Part |
1 |
Y_Axis_Belt_Bearing_Idler_Outide_LITE_Cable |
| RAMPS 1.4 Case LID |
Printed Part |
1 |
Ramps_1.4_Case_Lid |
| RAMPS 1.4 Case |
Printed Part |
1 |
Ramps_1.4_Case |
| Drag Chain Y Carriage Mount |
Printed Part |
1 |
Drag_Chain_Y_Carriage_Mount |
| X Axis Drag Chain Mount Y Side panel |
Printed Part |
1 |
X_Axis_Drag_Chain_Mount_Y_Side_panel |
| Root 3 Lite foot |
Printed Part |
4 |
Y_Axis_Box_Lite |
| X Carriage Back Panel |
Printed Part |
1 |
X_Axis_Carriage_Back_Panel |
| Spindle Clamp 52mm TOP |
Printed Part |
1 |
Spindle_Clamp_52mm |
| Spindle Clamp 52mm Bottom |
Printed Part |
1 |
Spindle_Clamp_52mm (Mirrored in Z) |
| X axis LITE mount |
Printed Part |
2 |
X_Axis_Mount_Wider |
| X Carriage Belt Idler |
Printed Part |
1 |
X_Axis_Carriage_Belt_Idler |
| Carriage Lite |
Printed Part |
6 |
X_Y_Axis_Carriage_Lite |
| Z Carriage Lite |
Printed Part |
2 |
Z_Axis_Carriage_Lite |
| X Axis Belt Plate |
Printed Part |
2 |
X_Axis_Belt_Clamp_Spacer |
| X Axis Belt Mount |
Printed Part |
2 |
X_Axis_Belt_Clamp_GT2 |
| LED Light Mount |
Printed Part |
1 |
Light_mount |
| NEMA17 |
Electronics |
4 |
4800g/cm holding torque min recomened |
| Microswitch KW11i |
Electronics |
6 |
|
| DC Spindle |
Electronics |
1 |
|
| Ramps 1.4 |
Electronics |
1 |
|
| Arduino Mega |
Electronics |
1 |
|
| DRV8825 |
Electronics |
4 |
|
| 12V PSU |
Electronics |
1 |
Wattage subject to stepper motors and spindle (If powered by 12V) |
| Spindle PSU |
Electronics |
1 |
Subject to Spindle requirments (I use 24V but plan to use 48V) |
| 20 x 20 mm Box section (length = 350mm) |
Hardware |
4 |
|
| 8mm Connecting Rod (Length = 430mm) |
Hardware |
1 |
8mm Smooth Rod |
| 8mm Z axis Rods (Length = 160mm) |
Hardware |
2 |
8mm Smooth Rod |
| LM8UU Bearings (Z axis) |
Hardware |
4 |
|
| 8mm Lead screw (2mm/Rev) (Length = 180mm) |
Hardware |
1 |
Z Axis lead screw |
| 8mm Collar |
Hardware |
1 |
|
| GT2 Pulley 5mm Bore (16T) |
Hardware |
4 |
|
| GT2 Pullet 8mm Bore (22T) |
Hardware |
3 |
|
| GT2 Belt (Length = 3m) |
Hardware |
1 |
|
| GT2 Closed loop belth (232T) |
Hardware |
1 |
|
| M8 Coach bolt L = 45mm |
Hardware |
4 |
Can use normal bolt |
| M8 Nut |
Hardware |
4 |
5 if using a normal threaded rod for the Z axis |
| M8 Washer |
Hardware |
4 |
8 if using normal hex head bolts |
| 608 Bearing |
Hardware |
12 |
|
| M5 x 20 mm Hex head bolt |
Hardware |
32 |
|
| M5 x 60 mm Bolt |
Hardware |
16 |
|
| 5mm Smooth Rod (Length = 30mm ) |
Hardware |
2 |
Used for the X axis Idler |
| M5 Washer |
Hardware |
112 |
|
| 625 Bearing |
Hardware |
38 |
|
| Base Board |
Hardware |
1 |
|
| Side Panel |
Hardware |
2 |
|